The beeper bomb: build a pager bomb without c4 for under $30. Ascii spex included.
64befa4ed682b23d96ce11ab05cf34a3<html>
<title> pimp issue four </title>
</head>
<body bgcolor="black" text="white" link="#63C6DE" vlink="skyblue" alink=
"skyblue">
<font color=white size=2>
<br>
<br>
<pre>
_ _ _______ _____ ___ ___ ____ _
/___/ /___/ / / /__> /_
_ __/ _/ \ _/__/ _/__> _/____ _ _ _ _ _ _ _
/ I N D U S T R I E S
/ 1995
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% Probe Industries Magazine Phile #4 aka PIMP #4 %
% The Bravo/Lifestyle or Bravo/Lifestyle Plus Pager Bomb %
% This Manual tells you how to build za pager bomb. %
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
NOTE: Read all the little notes about things i've left in here, these are very
important so no kids who do this blow their head off. ALSO, this is only
the exact set up for bravo and lifestyle pagers. Pluses of those
versions also. It's your "standard" pager.
+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+
Initial start-up cost: $40.00 MAX
$3.00 small roll of copper wire
$10.00 small pipe components; 2 caps, one small 1 1/2 inch long tube
3/8" diameter.
$8.00 beeper housing <solid case at best buy is the best one>
$2.00 1 spst switch
$13.00 beeper buttons <many independant beeper dealers sell these in
silver and gold as replacements, you need them>
$4.00 for a calculator
Other items needed:
1 hot-glue gun, glue for the gun, 1 drill with a
VERY small bit, black powder, 1/2" spring
that is 3/8" in diameter or so, epoxy. 1 solder
iron w/ solder.1 1.5v AA battery.
NOTE: When using the epoxy, get the mix you must do yourself, so it is
a "cool" mixture, no heat given off.
+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+-=-+
-=-=-=-=-=-
Quik Intro:
-=-=-=-=-=-
This phile will not tell you how to make a pager bomb that will take
out anyone within 20 ft of it. It is to show how to make a pager bomb
that will kill, if not maim severely the person who attempts to turn it
on. The pipe bomb enclosed worx as though the caps are bullets. Yes, a
LOT of momentum is given off from the bomb and the inside cap(s) will be
the propellant blowing out the top of the pager. There will also be the
normal shrapnel from the rest of the bomb. This will not kill anyone.
The propellant may.
Ok, all the parts listed are not necessarily needed brand new. The
buttons give the "real" looking effect. The spst switch must be a very
small slide one. There is a standard one that is just like the one in
pagers that is sold at radio shack. The beeper case you can buy at best
buy, dirt cheap, and make sure it's not see-thru.The calculator can just
be an old broken one, but the lcd is needed out of it, or if you can get
a small lcd an easier way, go for it. If you cannot get gun powder in a
canister or any legit way, open up forty firecrackers, not that this is
the best powder to use, it is not NEAR decent, but will work.
STEPS:
1. To start, build the pipe bomb. Using the copper wiring so it will be
electronically set off by a charge. Use the drill and that small bit to make
the holes. There are 10,320,543,853 files out there on how to build a pipe
bomb. read them, im not going to splain myself with diagrams and such. it's
easy damn it.
2. after the pipe bomb is done and you have the two wire coming from it, start
work on "preparing the beeper case". first, take the lcd off of the
calculator. you must also grab the plastic cover off of it. the lcd might be
sticky and may need to be ripped off of the glass. do so and try to get all
the stickey stuff off.. it looks much more realistic if clean. cut the
plastic covering to fit the grooves in the top of the pager case. cut it
until it slides in perfectly; this isnt hard. then cut the lcd papery gray
thingee the be slightly larger then the plastic cover and slide it behind the
plastic cover. Hot glue the paper to the case from the BACK side of it. this
should all be done in the area labeled as 1a in the diagram below.
3. drop the two buttons in accordingly, the arrow up button (1b) going on the
side where the battery gets inserted, the other button (1c) on the other
side.drop hot glue over these, a LOT of hot glue to keep them on even when
pressed.
4. next, take your single pole single throw mini-slide switch.on the far left
prong solder a 1 1/2" small wire from there to the 1/2" spring. solder
another piece of wire to the middle prong. slide the spring longways so the
end would be pressin on the head of a battery right over where the arrow
button is and epoxy it down (1d.). lay the switch down where a slot is cut
out in the side for it (1e.). Epoxy it to the side making sure there is NO
give. This must be a very strong seal; Epoxy it so when the slide is switched
downwards <towards the bottom of the case> the middle prong is connect to the
unused prong. KEEP IT THAT WAY.
5. insert the battery thru the bottom hole, making sure the pipe bomb is no
where near this circuit yet. close the door on the bottom and lock it. the
battery should be pushing against the spring (1f.). the POSITIVE side should
be pusing against the spring. here comes the tricky part. Take another piece
of wire, about an inch long and slide one stipped end into a little loop
hanging out of the bottom <on the inside of the case of course>. it's a loop
coming from the bottom door. Hook the stripped end into there (1g.). since
solder gets kinda hot, drop some epoxy over the connection.
6. HERE IS THE HARD PART: placing the bomb inside and sealing it.
Making sure the switch is turned OFF <thats all the way down, making
sure the terminal prong with nothing connected to it is the part with
the switch over it>, slowly place the pipe bomb into the open side of
the casing. DO THIS ONLY AFTER ALL THE HEAT FROM OTHER WORK IS GONE.
take one wire from the p-bomb and twist it to the bottom wire.
take the other piece and connect it to the middle terminal prong wire
off of the switch, MAKING SURE FIRST THE SWITCH IS OFF. make sure these
are twisted good and epoxy is "dropped" over them. epoxy the bomb to
the casing (1h.). slowly place the back of the pager case onto it, with
the bottom ridges interlocking with the bottom of the back piece and
where the little bolts go in the top, either buy little hexbolts,or when
you have let it sit for 5 minutes,drop a drop or 2 of glue in the holes,
without touching the nose of the gun to the casing. wipe off any excess
glue to make it "unnoticeable".
NOTE: the next person who turns the switch "on" the pager, gets toasted. it
weighs the same weight <practically> as a regular pager
Diagram: this is the pager face down with the back off.
1a.
/ \
/ \
___________________________________________
| |
| _______ _______ |
| | 1c. | | 1b. | |
| |_____| |_____| 1d. |
|
1e. |
| |
| |
| |
| |
| |
| 1f. |
| |
| 1h. |
| |
| |
| |
| |
| |
| 1g. |
|_____________________x_____________________|
+---------------------------------------------------------------+
--+ ]{ Brought to you by -+fringe+- }[ +--
of
____ ____ ___ ___ ___
_/__/ _/__/ _/ / _/__> _/_
_/ _/ _> _/__/ _/__> _/__
I N D U S T R I E S
For all the diehard H/Per's out there, call the following boards:
Apocalypse 2000 +1-847-831-0484
Poisoned Pen +1-847-966-2095
</pre>
<a href=index.shtml>GO BACK...</a><br>
</body>
</html>
© 2012 Packet Storm. All rights reserved.
%7Cutmcsr%3D(direct)%7Cutmcmd%3D(none)){kind=small}
Follow us on Twitter
Follow us on Facebook
Subscribe to an RSS Feed
Comments
No comments yet, be the first!